Compact pulper for defibration of dry samples on a laboratory scale.
Frame and vessel made of stainless steel.
Available in three sizes: 8 litre, 20 litre and 45 litre.
Rapid defibration of virgin and secondary fibres.
Pulping up to 350 g (o.d.) of pulp.
Adjustable speed from 100 to 1,400 rpm.
Consistency range 2 % to 7 %.
For quick and reproducible determining the mean thickness and thickness distribution of wood chips intended for the production of chemical or mechanical pulps. Heavy and robust construction with motor and control panel built in. Lightweight trays made of stainless steel and aluminium. Standard screens: 45 mm round hole, 8 mm slot, 13 mm round hole, 7 mm round hole, 3 mm round hole, dust pan.
Applicable standards: SCAN CM 40/88, TAPPI UM21, GOST (round version)
For laboratory beating of chemical or semi-chemical pulps under standardized conditions.
Classified by EUCEPA as the best laboratory beater and recommended in ISO 5264
Recommended in ISO 5269-2
Applicable Standards: ISO 5 264/2, DIN-EN 25 264-2, SCAN C 24, TAPPI T248, PAPTAC C.7
A simple and rapid method of determining the consistency of a pulp suspension. More rapid than the Buchner funnel method and suitable for use with most types of pulp.Robust, corrosion resistant, stainless steel construction. Rapid operation. Easy to use. Used in freeness tests. Used with an automated Laboratory Beater. Consistency determination.
For beating of pulp under standardized conditions for laboratory purposes.
Stainless steel construction. Volume 23 litres (at a consistency of 1.57 %) Beatable amount of pulp: 360 g (o.d.)
Applicable Standards: TAPPI T200m, TAPPI T205m, ISO 5246-1, SCAN C25, CPPA C.2
For the determination of fibre length of pulp by classification.
Mounting frame and classification units made entirely of stainless steel. Quick-locks for screens and drainage cups. Vacuum pump to speed up the drainage at the end of the test. Standard screens: ASTM 16 / 30 / 50 / 100 / 200. Ideal for upstream mounting of shive content analyser like Somerville Screen, Haindl Classifier, or Brecht-Holl Classifier. Fully automatic testing.
Applicable Standards: SCAN M6, TAPPI T 223, PAPTAC C5V
For determination of the shive content in pulp.
Standard slot plate with 0,15 mm width
Slot plate with 0,08 and 0,1 mm width optionally available
Robust stainless steel version.
Control cabinet for wall fastening delivered with the instrument.
Applicable Standards: TAPPI T275, UM 242, PAPTAC C.11P
SCHOPPER RIEGLER
FREENESS TESTERS
DIGITAL, PNEUMATIC OR MANUAL
For the determination of the degree of refining (beating) of a pulp
suspension in water and expressing it in terms of the Schopper-Riegler
(SR) number, and to determine the dewatering time. Made entirely of
stainless steel materials. 5 models available. Mechanical. Pneumatic.
Digital: Electronic determination of results with digital display and data
transfer (pneumatic lifting). The Schopper-Riegler apparatus is a primary
tool in the evaluation of the characteristics of pulp.
Applicable standards: ISO 5 267/1, SCAN C 19 M3, BS 6035/1
/7/6
CANADIAN STANDARD FREENESS TESTERS
For measuring the rate of drainage of a dilute pulp suspension and
expressing it in terms of freeness. Constructed entirely of stainless steel materials.
Three Models available: -HM1P41510 - Mechanical model.
HM1P41511 - Electronic determination of results with digital display and
data transfer (pneumatic lifting).
HM1P41512 – Electronic determination of results with digital display,
data transfer, with temperature compensation and consistency correction.
Applicable standards: ISO 5267-2, TAPPI T 227, SCAN C21 and M4, PAPTAC
C.1, APPITA P260
/11/12
To determine the freeness value and rate of drainage of pulp, mechanical and ground wood pulp suspensions according to the Schopper Riegler method.
Bench mounted instrument with semi automatic lifting of the sealing cone and agitation of the pulp ensures ease of use.
Robust construction using corrosion resistant materials ensures low maintenance....
DISINTEGRATOR
For the standardized disintegration of pulp suspensions
Made of all corrosion resistant materials. Upper part swings open for
ease of use. Motor capacity: 250W.
Electronic counter of revolutions. Electronics built into the upper part
of the instrument and therefore well protected against water ingress.
Disintegration pot is available in Plexiglas® (standard) or stainless
steel.
Applicable standards: ISO 5263-1, TAPPI T205, SCAN
C18/M2, PAPTAC C.6,
For homogenisation and continuous stirring of disintegrated pulp suspension. Wall mounting or with an optional stand for bench top operation. Sturdy construction made of stainless steel and Plexiglass®.
Tap and spout for easy filling and cleaning. Quiet geared motor (3 dbA).
Plexiglass® pot for 12 litre suspension. Optionally for 24 litre suspension. Construction according to standard.
HM1P95555
TAPPI SHEET MACHINE - manual
For the production of
standardised hand sheets (159 mm diameter).
TAPPI standard (159 mm diameter. Sheet forming with manual mixing.
Couching with supplied couch roll. De-watering only by gravitation, no
vacuum pump necessary. Manual
agitation with supplied stirrer. De-watering
via ball valve. Couching with supplied couch disc and couch roller. For
the drying process polished stainless steel discs and drying rings are
included.
Applicable
standards: ISO
5269/1, TAPPI T205, SCAN C26, AS.NZ S 1301.214s
(Conventional sheet-former method). For the semi-automatic production of standardised hand sheets. Available sizes: TAPPI standard (159 mm diameter), KCL or other standards (165 x 165, 250 x 250 mm, 215 mm diameter…)
Pneumatic couching. De-watering only by gravitation, no vacuum as in the Rapid-Köthen system. Stainless steel materials. Semi-automatic version to built-in into a laboratory table.
Applicable standards: ISO 5269/1, TAPPI T205, SCAN C26, AS/NZ 1301.214s.
Automatic Rapid Köthen sheet former for the production of standardised hand-sheets (200 mm diameter). PLC controlled process for automatic sheet forming. Process can also be carried out manually.Strong stainless steel frame with waterproof polypropylene working top.Lightweight dryer lids for easy handling. Simple push-button control to start/stop the drying process. Drying time for standard hand-sheets, (3 – 6 min). Optional white water re-circulation system. Optional dryers up to 145°C (standard is up to 97°C).
Applicable standards: ISO 5269-2, Zellcheming Merklatt V/8/76, DIN 54358
For de-watering and pressing of laboratory hand sheets, produced on TAPPI sheet machines. Heavy and robust, Easy to operate. Two programmable pressing cycles. Completely non-corroding materials. Acrylic glass covers.Four pneumatic cylinders for even pressure distribution. Water drain at the back. Pressing area 350 x 350 mm. Minimal Maintenance. Maximum pressing force at 6 bar supply pressure: 18,500 N- at 8 bar supply pressure: 24,250 N
For the rapid drying of hand sheets after pressing or for determining the dry content of hand sheets or pulp for speedy evaluation.
Robust stainless steel construction and anodized aluminium hotplate ensure precise heat distribution.
Applicable Standard: TAPPI T205